We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Polymers of micro(nano) plastic in household tap water of the Barcelona Metropolitan Area
AI summary Read the abstract
Researchers developed a workflow using toluene extraction and advanced polymer chromatography coupled to high-resolution mass spectrometry to identify and quantify micro and nanoplastic polymers between 0.7 and 20 micrometers in tap water. Applying the method to samples from 42 postal codes in the Barcelona Metropolitan Area detected polyethylene, polypropylene, polyisoprene, and polybutadiene in drinking water.
Microplastics (MPLs) are emerging persistent pollutants affecting drinking water systems, and different studies have reported their presence in tap water. However, most of the work has a focus on particles in the 100-5 µm range. Here, a workflow to identify and quantify polymers of micro and nanoplastics (MNPLs), with sizes from 0.7 to 20 µm in tap water, is presented. The analytical method consisted of water fractionated filtration followed by toluene ultrasonic-assisted extraction and size-exclusion chromatography, using an advanced polymer chromatography column coupled to high-resolution mass spectrometry with atmospheric pressure photoionization source with negative and positive ionization conditions (HPLC(APC)-APPI(±)-HRMS) and normal phase chromatography HILIC LUNA® column and electrospray ionisation source in positive and negative mode (HPLC(HILIC)-ESI(±)-HRMS). The acquisition was performed in full scan mode, and the subsequent tentative identification of MNPLs polymers has been based on increasing the confirmation level, including the characterisation of monomers by using Kendrick Mass Defect (KMD) analysis, and confirmation and quantification using standards. This approach was applied to assess MNPLs in tap water samples of the Barcelona Metropolitan Area (BMA), that were collected from August to October 2020 from home taps of volunteers distributed in the 42 postal codes of the BMA. Polyethylene (PE), polypropylene (PP), polyisoprene (PI), polybutadiene (PBD), polystyrene (PS), polyamide (PA), and polydimethylsiloxanes (PDMS) were identified. PE, PP, and PA were the most highly detected polymers, and PI and PBD were found at the highest concentrations (9,143 and 1,897 ng/L, respectively). A principal component analysis (PCA) was conducted to assess differences in MNPLs occurrence in drinking water, that was provided from the two drinking water treatment plants (DWTPs) suppliers. Results showed that no significant differences (at 95% confidence level) were established between the drinking water supplies to the different areas of the BMA.
More Papers Like This
Polymers of micro- and nanoplastics in household tap water of Barcelona
AI summary Read the abstract
Researchers quantified micro- and nanoplastic polymers in the 0.7-20 micrometer size range in household tap water from the public drinking water network of Barcelona, Spain, using a novel workflow designed to capture smaller particle sizes than most previous studies. The cross-sectional study found microplastics present in drinking water at concentrations relevant to human daily exposure assessment.
Quantitative analysis of nanoplastics in environmental and potable waters by pyrolysis-gas chromatography–mass spectrometry
AI summary Read the abstract
Scientists developed and validated a new method to detect and measure nine types of nanoplastics in drinking and environmental water at very low concentrations. They found nanoplastics in every water sample tested, with polyethylene, PET, polypropylene, and polystyrene being the most common at levels up to 1.17 micrograms per liter. This is one of the first studies to quantify nanoplastics in drinking water, confirming that people are regularly exposed through their tap water.
Routine method for the analysis of microplastics in natural and drinking water by pyrolysis coupled to gas chromatography-mass spectrometry
AI summary Read the abstract
Researchers developed a standardized method to measure microplastics in drinking water using a technique called pyrolysis gas chromatography-mass spectrometry. They tested the method on river water, reclaimed water, and tap water in Barcelona, finding microplastic concentrations ranging from 11 to 77 micrograms per liter. Reliable detection methods like this are essential for understanding how much microplastic people are actually consuming through their drinking water.
Microplastics in the drinking water supply system: analysis of water from the source to the tap by pyrolysis-GC-MS
AI summary Read the abstract
Researchers analyzed microplastic concentrations in raw, treated, and tap water from the Amsterdam drinking water supply system over six months using pyrolysis-GC-MS, targeting six common polymers including PE, PP, PS, PET, PVC, and PMMA. PE and PVC were frequently detected in tap water, contributing new data on MP levels throughout the full drinking water supply chain and their implications for human exposure estimation.
Exposure to micro(nano)plastics polymers in water stored in single-use plastic bottles.
AI summary Read the abstract
Researchers quantified micro(nano)plastics ranging from 700 nm to 20 µm in bottled water from 20 popular Spanish brands, assessing daily consumer exposure risk and raising concern about the widespread presence of plastic polymer particles in single-use bottled water.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.