We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Comparative Performance of Magnetic Iron Oxide Nanoparticles in Removing Polyethylene Micro- and Nanoplastics from Model Water Systems
AI summary Read the abstract
Tiny iron oxide particles, made using three different lab methods and sometimes coated with other chemicals, were tested for removing polyethylene micro- and nanoplastics from water samples in the lab. Removal success ranged from about 34% to 93%, with uncoated particles made by one method and coated particles made by another method performing best.
Abstract In this study, magnetic iron oxide nanoparticles (MIONs) were synthesized using three different. methods: coprecipitation, microwave-assisted synthesis, and hydrothermal synthesis. The resulting nanoparticles were further functionalized with citric acid (CA) and cetyltrimethylammonium bromide (CTAB) to enhance their physicochemical properties and adsorption capabilities. Comprehensive characterization was carried out using thermogravimetric analysis (TGA), Fourier Transform Infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), electrokinetic measurements of zeta potential (ZP), transmission electron microscopy (TEM), and magnetic measurements. The synthesized MIONs were applied for the removal of polyethylene (PE) micro- and nanoplastics (MPs and NPs) from aqueous solutions. TGA and FTIR analyses confirmed successful functionalization, particularly with CA, where up to 45% mass loss was attributed to the decomposition of the coating agent. Zeta potential measurements revealed a significant shift in the isoelectric point (IEP), further confirming surface modification. The removal efficiencies varied between 33.56% and 93.39%, with the highest efficiency achieved using unmodified hydrothermally synthesized MIONs. Interestingly, CTAB-functionalized MIONs synthesized via coprecipitation also exhibited high adsorption capacities, reaching up to 118.2 mg/g. The superior performance of the bare hydrothermal particles and the good performance of the CTAB-coated coprecipitated particles may reflect differences in particle properties and surface chemistry that favor interactions with MPs and NPs. Post-removal characterization indicated partial adsorption of PE on the MIONs surface, as shown by increased mass loss in TGA curves and subtle changes in FTIR spectra. Magnetic measurements demonstrated a decrease in magnetization after functionalization, as expected, but the MIONs retained sufficient magnetic responsiveness for separation processes. Overall, CTAB-functionalized MIONs synthesized via the coprecipitation and unmodified hydrothermally synthesized MIONs were identified as the most promising candidates for PE MPs and NPs removal. The results further demonstrated that the effect of surface functionalization strongly depends on the synthesis route and nanoparticle properties, as functionalization did not universally improve removal efficiency. This study highlights the importance of synthesis route and surface chemistry in the design of magnetic nanomaterials for PE MPs and NPs removal from model aqueous systems.
More Papers Like This
Testing an Iron Oxide Nanoparticle-Based Method for Magnetic Separation of Nanoplastics and Microplastics from Water
AI summary Read the abstract
Researchers tested iron oxide nanoparticles with hydrophobic coatings as a method for magnetically separating micro- and nanoplastics from water. The approach achieved 100% removal of larger microplastics and nearly 90% removal of nanoplastics using a simple permanent magnet, suggesting a viable method for water purification and environmental monitoring.
Removal of microplastics from water by magnetic nano-Fe3O4
AI summary Read the abstract
Researchers developed a method for removing microplastics from water using magnetic iron oxide nanoparticles that attach to plastic surfaces, allowing the particles to be pulled out with a magnet. The technique achieved removal rates above 80% for common microplastic types in environmental water samples including river water, sewage, and seawater, suggesting a practical approach for water treatment.
Effective removal of Micro- and nanoplastics from water using Iron oxide nanoparticles: Mechanisms and optimization
AI summary Read the abstract
Researchers developed a magnetic separation method using iron oxide nanoparticles to remove micro- and nanoplastics from water, achieving up to 95% removal efficiency within just 20 minutes. The technique works through hydrophobic interactions between the iron oxide particles and plastic surfaces, and was particularly effective for smaller nanoplastics. The method offers a relatively simple, rapid, and cost-effective approach to filtering plastic particles from contaminated water.
Magnetic Removal of Micro‐ and Nanoplastics from Water—from 100 nm to 100 µm Debris Size
AI summary Read the abstract
Researchers demonstrated a magnetic method for removing micro- and nanoplastics from water using iron oxide nanoparticles that attract oppositely charged plastic particles. The technique was effective across a wide size range, from 100 nanometers to 100 micrometers, and worked with multiple plastic types. The study suggests that magnetic removal could help address the gap in current wastewater treatment, which struggles to capture the smallest plastic particles.
Removal of Micro and Nano Plastics from Water Using Magnetic Nanoparticles
AI summary Read the abstract
Researchers evaluated surface-functionalized magnetic nanoparticles for removing micro- and nanoplastics from water, optimizing pH, dosage, contact time, and agitation to maximize removal efficiency, and found the approach outperforms conventional treatment while offering rapid magnetic separation and nanoparticle reusability.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.