We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Low-Cost 3D-Printed Kaolin–Rice-Husk Microporous Membranes for Microplastic Removal: A Comparative Study with a Commercial Ceramic Membrane
AI summary Read the abstract
Researchers made a low-cost filter from clay and rice husks using 3D printing, then tested how well it filtered plastic particles from water compared to an expensive commercial ceramic filter. The low-cost filter fully removed larger microplastic particles but caught fewer of the smallest ones, while costing about 94.5% less than the commercial version.
Microplastics (MPs) are pervasive emerging contaminants in freshwater and drinking-water systems, and conventional treatment processes may achieve insufficient removal of smaller MP fractions. Membrane filtration provides an effective barrier to MPs; however, commercial ceramic membranes can be relatively expensive. In this work, low-cost porous ceramic membranes were fabricated by extrusion-based three-dimensional (3D) printing of a kaolin–rice husk paste, followed by sintering at 1200 °C. The removal of model spherical polyethylene (PE) and irregularly shaped polyethylene terephthalate (PET) MPs across different particle-size fractions was evaluated using dead-end filtration and benchmarked against a commercial ceramic membrane. The 3D-printed membrane removed 58.3 ± 3.6% of 1–10 µm PE particles, while complete removal was achieved for the 75–90, 300–355, and 600–710 µm PE fractions. For PET, removal efficiencies of 80.8 ± 0.9%, 94.9 ± 1.8%, and 100% were obtained for the 10–45, 45–75, and 75–150 µm fractions, respectively. By comparison, the commercial membrane achieved 100% removal across all PE and PET fractions tested. The fabricated membrane had a modal pore size of 0.80 µm and an estimated cost of USD 2.98, compared with USD 54.45 for the commercial 0.45 µm membrane. Thus, the 3D-printed membrane effectively removed medium and large MP fractions, while its estimated fabrication cost was approximately 94.5% lower than the purchase cost of the commercial membrane used for comparison. Although its larger pore size resulted in incomplete removal of the smallest MP fractions, the combination of effective removal of larger MPs and substantially lower estimated fabrication cost demonstrates the potential of extrusion-based 3D printing as an alternative approach for producing ceramic membranes for MP removal.
More Papers Like This
Removal of Microplastics and Performance of a Developed Ceramic Filter
AI summary Read the abstract
Researchers developed a ceramic filter from clay and waste glass with varying porogenic agent content and firing temperatures, then evaluated water permeability, element leaching, and microplastic removal efficiency. The formulation without a porogenic agent achieved the highest microplastic removal rate of nearly 99.8%, demonstrating that optimizing porosity and filtration pressure is key to effective and affordable microplastic filtration.
Rice Husk Biochar Filtration for Microplastic Removal from Raw Water at a Drinking-Water Depot in Aceh Besar, Indonesia
AI summary Read the abstract
Tiny plastic particles too small to catch with normal water treatment are turning up in drinking water, especially from small local water refill stations. This study found that filtering water through biochar made from burnt rice husks, a cheap, plant-based material, can effectively strip out these microplastics before the water reaches your glass. It's a promising, low-cost solution that could help reduce your exposure to microplastics without requiring expensive treatment upgrades.
Fabrication of low-cost ceramic microfiltration membranes with controllable pore size distribution using nanometer attapulgite for gravity-driven filtration of microplastic-contaminated roofing rainwater
AI summary Read the abstract
Low-cost ceramic microfiltration membranes were fabricated for water purification, demonstrating effective removal of suspended particles including microplastics from contaminated water. Affordable membrane materials are important for making microplastic removal accessible in low-resource settings.
Removal of synthetic and toothpaste derived microplastics from wastewater using low-cost fuller's earth and bagasse ash ceramic membrane
AI summary Read the abstract
Researchers fabricated low-cost ceramic membranes from fuller's earth clay and sugarcane bagasse ash and demonstrated greater than 95–99.5% removal efficiency for a composite of nine polymer types including PE, PS, PET, PVC, and nylon, with the membrane also successfully separating microplastics from toothpaste-derived wastewater at a material cost of roughly $53 per square meter.
Low-cost silica based ceramic supported thin film composite hollow fiber membrane from guinea corn husk ash for efficient removal of microplastic from aqueous solution
AI summary Read the abstract
A low-cost ceramic hollow fiber membrane fabricated from guinea corn husk ash silica was developed and tested for microplastic removal from water, achieving high rejection rates for particles above 1 micrometer and offering a scalable, affordable filtration option for regions lacking expensive commercial membranes.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.