0
Article Sign in to save

Laboratory Evaluation of Wear Particle Emissions and Suspended Dust in Tire–Asphalt Concrete Pavement Friction

EcoVision Journal of Environmental Solutions 2024 4 citations

AI summary Read the abstract

Every time tires roll on pavement, they shed tiny particles of rubber and asphalt dust, a source of microplastic pollution that's been linked to health concerns when inhaled or when it washes into waterways. This lab study found that using asphalt with smaller stone particles in road pavement can cut this wear-and-tear dust by up to 20%, suggesting that smarter road design could be a simple way to reduce microplastic pollution from everyday driving. The researchers also created a testing method that could help engineers evaluate and choose lower-dust pavement materials before roads are even built.

This study aims to evaluate the tire–road-wear particles (TRWPs) and suspended dust generated based on the nominal maximum aggregate size (NMAS) of the polymer-modified stone mastic asphalt (SMA) mixtures indoors. The SMA mixtures containing styrene butadiene styrene (SBS) polymer and the NMASs of 19, 13, 10, 8, and 6 mm were used. Dust was generated from the wear of the tires and the pavement inside the indoor chamber by using the laboratory tire–road-wear particle generation and evaluation tester (LTRWP tester) developed by Korea Expressway Corporation (KEC). In this method, a cylindrical asphalt-mixture specimen rotates in the center, and a load is applied using three tires on the sides of the test specimen. During the test, a digital sensor was used to measure the concentration for each particle size. After the test was completed, the dust was collected and weighed. According to the test results, the generated TRWP emissions were reduced by approximately 0.15 g as the NMAS of the SMA mixture decreased by 1 mm. TRWP emissions decreased by 20% when using the 6 mm SMA mixture compared to the 13 mm SMA mixture. For practical application, a predicted equation of TRWP emissions estimation was developed by using the concentration of suspended dust measured by the digital sensor in the LTRWP tester. LTRWP can be used as an indoor test method to evaluate pavement and tire materials to reduce the amount of dust generated from tire and pavement wear.

More Papers Like This

Article

Advancing tire and road wear particles (TRWP) measurements : balancing laboratory conditions and real-world relevance

AI summary Read the abstract

Researchers used a pin-on-disc tribometer to investigate tyre and road wear particle (TRWP) generation under varying urban load and sliding speed conditions, finding that airborne emissions were near zero under moderate conditions but increased sharply under harsh contact conditions, underscoring the importance of realistic test parameters.

Article Tier 2

Characterization of airborne tire particle emissions under realistic conditions on the chassis dynamometer, on the test track, and on the road

AI summary Read the abstract

Researchers developed a new tire and road wear particle (TRWP) sampling system and characterized airborne emissions under real-world conditions on a chassis dynamometer, test track, and public road. Emissions showed a bimodal size distribution with dominant modes at ~10 nm and 270 nm, with SEM/EDS revealing two particle formation mechanisms and confirming tire rubber as a major source of ultrafine airborne particles.

Article

A Variety of Particles Including Tire Wear Particles Produced on the Road

AI summary Read the abstract

This study analyzed the types and shapes of various particles generated on asphalt pavement roads, finding tire-road wear particles, asphalt wear particles, glass beads, road paint wear particles, and plastic particles across different size fractions. Tire wear particles smaller than 212 µm dominated, with rough-surfaced mineral particles likely accelerating tire abrasion.

Article Tier 2

Shades of grey—tire characteristics and road surface influence tire and road wear particle (TRWP) abundance and physicochemical properties

AI summary Read the abstract

A suite of experiments characterized how tire type, compound, and road surface properties influence tire and road wear particle (TRWP) size, morphology, and emission rates, finding significant variation across tire and road combinations relevant to predicting environmental exposure.

Article Tier 2

Characteristics of Vehicle Tire and Road Wear Particles’ Size Distribution and Influencing Factors Examined via Laboratory Test

AI summary Read the abstract

Researchers conducted laboratory tests to characterize the size distribution of tire and road wear particles under various conditions. The study found that factors such as driving speed, tire composition, and road surface characteristics significantly influence the size and quantity of wear particles released, which are a growing source of microplastic pollution.

Research digests by email

When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.

Email me about

Share this paper