We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Harnessing the power of amphoterically modified Chitosan coagulants for enhanced Polyester microplastic fibre removal from water
Summary
Amphoterically modified chitosan was used as a coagulant aid to capture microplastics from water, leveraging the biopolymer's charge-switching ability to bind particles across a range of pH conditions. Chitosan-based capture materials are attractive because chitosan is biodegradable and derived from renewable sources.
Microplastic fibre (MPF) is the dominant type of microplastic present in water treatment plants' influent. Coagulation-flocculation followed by sedimentation effectively removes microplastics during pre-treatment; however, conventional inorganic coagulants produce high sludge volume, causing secondary pollution. Chitosan offers a greener alternative but is limited by poor solubility and low molecular weight. In this study, two amphoteric modifications were successfully incorporated into Chitosan, including CMC-CTA, synthesised by modifying carboxymethyl Chitosan (CMC) with 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CTA); and CMC-g-PDMC, synthesised by grafting poly[(2-methacryloyloxyethyl) trimethyl ammonium chloride] (PDMC) onto CMC. Their coagulation performance for MPF removal was assessed by turbidity measurement. The effects of coagulant dosage, solution pH and sedimentation time were systematically investigated. Zeta potential measurements, scanning electron microscopy (SEM) and Fourier-transformed infrared (FTIR) spectroscopy were employed to investigate the MPF removal mechanism. Among the three coagulants tested, CMC-CTA exhibited the lowest residual turbidity with a coagulant dosage as low as 1 mg/L. Both modified coagulants performed better at neutral to near-alkaline pH, with the lowest residual turbidity recorded at a pH of 8. The MPF removal mechanism by CMC-CTA and CMC-g-PDMC appeared to involve charge patching. These findings provide new insights into MPF removal via amphoteric Chitosan coagulants, particularly in neutral and near alkaline pH ranges, typical of water treatment plant influents.
Sign in to start a discussion.
More Papers Like This
Interaction of chitosan with nanoplastic in water: The effect of environmental conditions, particle properties, and potential for in situ remediation
Researchers tested chitosan — a natural polymer derived from shellfish — as a tool to aggregate and remove nanoplastic particles from water, finding it caused clumping at low doses but that high pH, dissolved organic matter, and surface chemistry of the plastics all affected its performance. The results suggest chitosan-based treatment has real potential for water remediation but requires careful tuning of environmental conditions.
The use of chitosan for water purification from microplastics
Researchers investigated chitosan as a sorbent for removing microplastics from water, analyzing its physicochemical properties and proposing an optimized purification method based on chitosan's sorption characteristics.
Utilization of chitosan as a natural coagulant for polyethylene microplastic removal
Scientists tested chitosan, a natural material derived from shellfish, as an eco-friendly way to remove polyethylene microplastics from water. Under the best conditions (pH 6.0 with 100 mg/L of chitosan), the treatment removed 81.5% of microplastics, offering a promising and environmentally safe approach to cleaning microplastic-contaminated water.
Synergistic removal of microplastic fibres: Integrating Chitosan coagulation in hybrid water pre-treatment systems
Microplastic fibers are the most common type of microplastic found entering water treatment plants, yet their elongated shape makes them especially hard to remove with conventional filters. This study investigated using chitosan — a natural, biodegradable material derived from crustacean shells — as a "green" coagulant to clump fibers together so they can be more easily removed, and also developed chemically modified versions of chitosan that work across a wider range of water conditions. The results showed that combining chitosan-based coagulation with microbubble aeration creates a synergistic pretreatment system that significantly improves microplastic fiber removal while avoiding the residual metal ions left by conventional chemical coagulants.
Integrated Chitosan-based coagulation and microbubble pre-treatment for improved microplastic fibre removal from water
Researchers developed a combined chitosan-based coagulation and microbubble pre-treatment system for removing microplastic fibres from water, finding that this approach overcame the limitations of conventional inorganic coagulants and improved removal efficiency for the morphologically challenging fibre fraction.