We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Methodology for removing microplastics and other anthropogenic microparticles from sludge dewatering system
AI summary Read the abstract
Researchers compared the recovery efficiency of anthropogenic microparticles from dewatered and digested sewage sludge using peroxidation combined with density separation in either sodium iodide (1.5 g/cm3) or sodium chloride (1.2 g/cm3) solutions. They found that the higher-density NaI solution recovered approximately 5-fold more microparticles than NaCl, identifying polyethylene, polypropylene, and ethylene-ethyl-acrylate copolymer as the dominant plastic types in sludge.
Anthropogenic microparticles (e.g., microplastics) are present in sewage plants, especially in sludge streams. However, the lack of standardized protocols to scrutinize the presence of anthropogenic microparticles in sludge makes the comparison between studies unfeasible. To tackle the knowledge gap regarding the efficiency of methodologies on the extraction of anthropogenic microparticles from the complex organic matrix, dewatered sludge, and digested sludge was treated with peroxidation and density separation, and the recovery of microparticles from these samples was investigated. The results showed that with the use of a higher density solution (NaI, 1.5 g/cm) a much better recovery of anthropogenic microparticles from sludge samples (approximately 1000 microparticles/g-dw and 2000 microparticles/g-dw, from dewatered and digested sludge, respectively) was achieved in comparison with the use of a lower density solution (NaCl, 1.2 g/cm) (200 microparticles/g-dw and 600 microparticles/g-dw from dewatered and digested sludge, respectively). Moreover, although the use of peroxidation is an essential step to break down the sludge structure and to release microparticles to the liquid phase, the use of peroxidation after or before density separation did not affect the overall recovery of microparticles. Polyethylene, polypropylene, and copolymer ethylene-ethyl-acrylate were the main microplastic fragments identified in digested sludge and dewatered sludge. However, no relation was observed between the method applied and the polymer recovered. Regarding the presence of anthropogenic microparticle in centrifuge effluent, 450 ± 212 microparticles/L were counted, and although little is known about this stream, in can be a relevant source of anthropogenic microparticles.
More Papers Like This
Selection of a density separation solution to study microplastics in tropical riverine sediment
AI summary Read the abstract
A comparison of density separation solutions for extracting microplastics from tropical riverine sediment found that sodium iodide and zinc chloride achieved higher recovery rates than sodium chloride for dense polymers, but cost and environmental safety concerns favor NaCl for use in developing countries.
Optimization of a method used for extracting microplastics from an organic matter-rich matrix and isolated particles assessment
AI summary Read the abstract
Researchers optimized a method for extracting microplastics from sewage sludge — a challenging organic-rich matrix — by combining density separation and chemical digestion steps, improving recovery rates and enabling more accurate characterization of sludge-associated microplastics.
Extraction of microplastics from sediment matrices: Experimental comparative analysis
AI summary Read the abstract
Extraction efficiencies of four methods for separating microplastics from sediment matrices were experimentally compared using spiked samples, finding that density separation with saturated NaCl was adequate for most polymer types but underperformed for high-density polymers, and that no single method achieved complete recovery across all particle sizes and shapes.
Fate of microplastics in sludge concentration: Experimental evaluation of gravity thickening and flotation processes
AI summary Read the abstract
Researchers tracked microplastics through two common wastewater sludge treatment processes — gravity thickening and dissolved air flotation — finding that polymer density strongly determines where plastics end up, with lighter HDPE escaping into wastewater streams while heavier particles stayed in sludge, suggesting these steps could be targeted for early microplastic removal.
Separation and identification of microplastics from soil and sewage sludge
AI summary Read the abstract
Six agricultural soils and three sewage sludges were tested with multiple MP extraction protocols including density flotation with NaCl, ZnCl₂, and NaI, with H₂O₂ pre-digestion of organic matter significantly improving recovery. The study identifies optimal conditions for extracting microplastics from high-organic-matter samples and highlights the inadequacy of water-based protocols for complex matrices.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.