We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Vertical transport and retention behavior of polystyrene nanoplastics in simulated hyporheic zone
AI summary Read the abstract
Researchers investigated polystyrene nanoplastic transport through quartz sand columns under varying flow rates, orientations, water saturation, salinity, and temperature, finding that high salinity was the most powerful driver of retention. Increasing salinity from 0 to 35 PSU caused the penetration rate of nanoplastics to drop from 100% to zero by compressing the electrical double layer and facilitating aggregation.
The ecological risk of microplastics (MPs) usually depends on their environmental behavior, however, few studies focused on the impact of hydrodynamic perturbations on the fate of MPs in hyporheic zone. This study chose quartz sand (250-425 μm) as simulated porous medium to investigate the transport of 100 nm polystyrene nanoplastics (PSNPs) under hydrodynamic factors, including flow rates (0.5, 1.0, and 2.0 mL/min), flow orientations (up-flow, down-flow, and horizontal-flow), and water saturations (50%, 80%, and 100%), as well as different salinities and temperatures. The breakthrough curves (BTCs) and retained profiles (RPs) of PSNPs were compared and analyzed by Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. Due to the small size and moderate density of PSNPs, as well as high flow rates, the flow orientation exhibited little effect on the PSNP transport. However, high flow rate, low salinity, high water saturation, and low temperature would facilitate the mobility of PSNPs. The increase in salinity from zero to 35 PSU (practical salinity units) caused the compression of electrical double layer and weakened the electrostatic repulsion between PSNPs and sands, which dramatically decreased the penetration rate from 100% to zero. Especially, the lower energy barrier of PSNPs-PSNPs at 3.5 and 35 PSU (16.45 kT and zero, respectively) facilitated the adsorption of PSNPs on sand via ripening mechanism. Due to the strong adsorption of PSNPs by sand at high salinity, the effect of flow rate on PSNP transport was more pronounced at low salinity. The mobility of PSNPs at 0.035 PSU was enhanced by 41.4%-75.3% as the flow rate increased from 0.5 to 2.0 mL/min, which was contributed from the reversible deposition in lower secondary energy minimum depth at low salinity and the stronger hydrodynamic drag force generated by the high flow rate. However, the sufficient molecular diffusion at low flow rate promoted the occupation of PSNPs on adsorption sites. In addition, the penetration rate of PSNPs decreased by 25.0% as the water saturation decreased from 100% to 50%, indicating that the film straining at the air-water interface would hinder the transport of PSNPs. Finally, temperature increase impeded the penetration of PSNPs by 6.26%-23.1% via blocking mechanism. Our results suggest that low-salinity, high-flow river systems may be at greater risk of MPs contamination due to enhanced vertical transport capability.
More Papers Like This
Investigating transport kinetics of polystyrene nanoplastics in saturated porous media
AI summary Read the abstract
Researchers investigated how ionic strength, pH, and organic matter influence the transport of polystyrene nanoplastics through saturated porous media using column experiments and DLVO modeling, finding that increasing sodium ion concentrations promote nanoplastic aggregation and reduce mobility in soil and groundwater systems.
Enhanced sinks of polystyrene nanoplastics (PSNPs) in marine sediment compared to freshwater sediment: Influencing factors and mechanisms
AI summary Read the abstract
Researchers compared nanoplastic transport through freshwater and marine sediment columns, finding that nanoplastics penetrate far more readily in freshwater (up to 90% breakthrough) than in marine sediments (under 9%), primarily because higher salinity causes aggregation and marine sediments have finer grain sizes that trap particles more effectively.
Effects of physicochemical factors on transport and retention of polystyrene microplastics (PS-MPs) in homogeneous and heterogeneous saturated porous media
AI summary Read the abstract
Researchers studied how polystyrene microplastics move through different types of underground soil and sand formations. They found that smaller sand grains, higher salt concentrations, and the presence of calcium ions all increased microplastic retention, while mixed soil layers created preferential flow paths that allowed some particles to break through faster. The findings help explain how microplastics could potentially contaminate groundwater aquifers.
Transport of polypropylene, polyvinyl chloride, polyethylene terephthalate and polymethyl methacrylate microplastics in porous media under gradient ionic strength
AI summary Read the abstract
Researchers used column experiments to study how four types of microplastics — polypropylene, PVC, PET, and PMMA — move through soil-like porous media under different salt concentrations. They found that increasing salinity reduces microplastic mobility by causing particles to stick to sand surfaces, which has implications for predicting how far microplastics can travel through soils to reach groundwater.
Transport of polystyrene nanoplastics in natural soils: Effect of soil properties, ionic strength and cation type
AI summary Read the abstract
Researchers used column experiments across three soil types to show that polystyrene nanoplastic transport is governed by soil iron and aluminum oxide content and pH — with high-pH, low-oxide soils allowing up to 97% nanoplastic passage — and that calcium ions and higher ionic strength significantly increase retention, revealing that soil chemistry strongly controls nanoplastic mobility toward groundwater.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.