We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Preparation and Application of Si@Al Adsorbents for Different Pollutants Removal from Aqueous Solution
Summary
Researchers prepared a low-cost Si@Al adsorbent from electroflocculation waste by mixing sodium silicate at a 4:1 ratio and calcining at 200 degrees Celsius, demonstrating its efficient removal of organic pollutants, antibiotics, and metal ions from aqueous solutions.
This study tried to use electroflocculating precipitated waste to prepare a Si@Al adsorbent by simply mixing sodium silicate at a mass ratio of 4:1 and calcining at 200 °C for 2 h. The adsorbent was low cost, high efficiency, and could remove a variety of contaminants (organic pollutants, antibiotics, and metal ions) from water. In this study, adsorbent characterization and pollutant adsorption experiments were carried out. The results showed that: Si@Al adsorbent had uniform particles, distinct layers, a loose porous appearance, and the internal structure was scattered without a crystal structure. The optimal adsorption conditions for tetracycline were as follows: dosage of adsorbent 2.0 g/L, reaction time 10 min, pH = 4.5, and tetracycline removal rate of 97.13%. The optimal adsorption conditions for MB (MB stands for methylene blue) were an adsorption dosage of 4.0 g/L, a reaction time of 15 min, pH = 4.5–8.5, and a removal rate of 96.39%. The optimal adsorption conditions for Cu were a 2.0 g/L dosage of adsorbent, a reaction time of 30 min, a pH of 8.5, and a highest removal rate of 97.47%. It was worth noting that the effect of temperature on TC, MB and Cu was not significant. At the same time, the kinetic fitting results showed that the adsorption of MB was more consistent with the quasi-second-order kinetic model, with R2 ranging from 0.9788 to 1.0000. The adsorption of TC and Cu was more consistent with the quasi-first-order kinetic model, with R2 ranging from 0.9598 to 0.9999 and 0.9844 to 0.9988, respectively. According to the results of thermodynamics, kinetics and zero potential point, the adsorption of tetracycline and methylene blue was mainly a physical adsorption, multilayer heterogeneous or single-layer homogeneous adsorption process. The adsorption of Cu was categorized as multi-layer heterogeneous chemical adsorption. The co-existing substances had little effect on the properties of the adsorbent, and the adsorbent could be recycled 5 times. Compared with other adsorbents, the results showed that the adsorbents had obvious advantages in terms of the raw material source, preparation method, time cost and removal effect. This study provided a “waste into treasure, green and efficient” multi-pollutant adsorption method.
Sign in to start a discussion.
More Papers Like This
Erythromycin Scavenging from Aqueous Solutions by Zeolitic Materials Derived from Fly Ash
Researchers synthesized zeolite materials from fly ash and tested them as sorbents for removing erythromycin antibiotic from water, finding effective removal over a range of conditions and demonstrating that fly ash zeolites are promising low-cost adsorbents for pharmaceutical contaminants in water treatment.
Composite Polysilicate Metal Coagulants for Simultaneous Removal of Organic Matter, Phosphorus, and Ammonium-Nitrogen: Effects of Metal/Silicate Molar Ratio and Basicity
Researchers prepared composite polysilicate metal (CSM) flocculants combining Fe3+ and Mg2+ ions in polysilicic acid and evaluated their performance for simultaneously removing organic matter, phosphorus, and ammonium-nitrogen from wastewater, finding that metal-to-silicate molar ratio and basicity significantly affect removal efficiency.
Tetracycline Removal from Water by Adsorption on Geomaterial, Activated Carbon and Clay Adsorbents
New geomaterial adsorbents made from clay, activated carbon, cement, and PVA polymer were synthesized and tested for tetracycline removal from water, achieving rapid equilibrium within 30 minutes and high adsorption capacity that was pH-dependent, offering a low-cost option for antibiotic contamination removal in wastewater treatment applications.
Removal of Microplastics from Wastewater by Methods of Electrocoagulation and Adsorption
This review examines electrocoagulation and adsorption methods for removing microplastics from wastewater, comparing them against conventional physical, chemical, and biological approaches in terms of removal efficiency, cost, and practical scalability.
Microcosmic mechanism analysis of the combined pollution of aged polystyrene with humic acid and its efficient removal by a composite coagulant
Researchers analyzed how aged polystyrene interacts with humic acid at the molecular level and developed a novel polyaluminum-titanium chloride composite coagulant that effectively removes these combined pollutants from water across different pH conditions.