We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Investigation of the adsorption kinetics, adsorption isotherms, and fixed-bed column experiments for polystyrene nanoplastics (PSNPs) by sand, biochar, activated carbon, and activated carbon felt
AI summary Read the abstract
Lab tests compared sand, biochar, activated carbon, and activated carbon felt for removing nanoscale plastic particles from water. Activated carbon felt removed the most plastic and worked fastest, likely due to its fibrous structure trapping particles rather than small pores alone, in both batch and column water-flow tests.
Nanoplastics (NPs) are difficult to remove from water matrices because their small size and colloidal stability limit capture by conventional treatment processes. In this study, sand, biochar, activated carbon (AC), and activated carbon felt (ACF) were compared under batch and fixed-bed column experiments to determine adsorption mechanisms of polystyrene nanoplastics (PSNPs) removal. Biochar, AC and ACF clearly outperformed sand in all tests, and ACF showed the adsorption rate that t 95% was 3.5 h, which means ACF took 3.5 h to reach 95% of its equilibrium adsorption capacity, 5 times faster than AC and 14 times faster than biochar. The maximum adsorption capacity of ACF was 17.7 ± 3.35 mg/g, whereas AC was 3.10 ± 0.55 mg/g and biochar was 1.70 ± 0.43 mg/g. However, as the average pore diameters of the three carbonaceous adsorbents (1.74–1.81 nm) were smaller than the single polystyrene nanoplastic (PSNP) diameter (200 nm), the adsorption mechanism cannot be explained by pore filling alone. Instead, the superior performance of ACF ostensibly due to accessible external surfaces, an open fibrous network, and enhanced physical interception. Fixed-bed column experiments confirmed a similar trend. The ACF demonstrated PSNPs breakthrough at ∼66 bed volumes, whereas biochar and AC showed breakthrough at 0 and 2 bed volumes, respectively. Overall, the results indicate that the three-dimensional fibrous architecture of ACF enhanced PSNP retention more strongly than nominal BET surface area alone under the tested conditions. Future work should quantify PSNPs and adsorbents surface charge, test natural water matrices, and evaluate regeneration and long-term column operation.
More Papers Like This
Adsorption performance of nanoplastics in carbon filtration column
AI summary Read the abstract
This study investigated the adsorption and removal of polystyrene nanoplastics in a carbon filtration column under varying experimental conditions including pH and ionic strength. Results showed that activated carbon effectively retained polystyrene nanoparticles, with column performance depending significantly on water chemistry.
Efficiency of adsorption of PSNPs using spontaneous magnetic biochar prepared from pyrolysis of municipal sludge and industrial red mud solid waste
AI summary Read the abstract
Researchers prepared a spontaneous magnetic biochar from municipal sludge and industrial red mud waste to remove polystyrene nanoplastics from water. The material achieved a 97.87% removal rate within 30 minutes, with electrostatic interactions identified as the primary adsorption mechanism. The magnetic properties of the biochar enabled easy solid-liquid separation without filtration, offering a practical approach for nanoplastic remediation using waste-derived materials.
Biochar and activated carbon for micro‐ and nanoplastic removal in aqueous systems: a systematic review on mechanisms, influencing factors, and performance
AI summary Read the abstract
This review combined 12 lab studies on using charcoal-like materials, biochar and activated carbon, to remove tiny plastic particles from water. Versions treated with iron compounds removed over 90% of particles in lab tests, but most experiments used artificial water and clean plastic samples, not real-world conditions.
Adsorption of polystyrene nanoplastics on sawdust-based activated carbons
AI summary Read the abstract
This study tested activated carbon filters made from sawdust waste for their ability to remove nanoplastics from water. The best-performing filter, activated with potassium hydroxide, had a very high surface area and effectively captured polystyrene nanoplastics through chemical interactions. This low-cost, waste-derived approach could help reduce the amount of nanoplastics in drinking water, which is important because these tiny particles can cross into body tissues.
Application of carbon-based adsorbents in the remediation of micro- and nanoplastics
AI summary Read the abstract
This review summarizes how carbon-based materials like activated carbon, biochar, and carbon nanotubes can be used to remove micro and nanoplastics from water through adsorption. These materials are attractive because they are low-cost, eco-friendly, and can be modified to improve their plastic-capturing ability. Better water filtration materials could help reduce the amount of microplastics that reach people through drinking water and food preparation.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.