0
Article Sign in to save

Development and characterization of a composite material with geopolymer matrix obtained by incorporation of microparticles from plastic bottles

World Congress on Medical Physics and Biomedical Engineering, September 7 - 12, 2009, Munich, Germany 2024 3 citations

AI summary Read the abstract

Researchers developed geopolymer composite materials incorporating ground PET plastic bottle particles, finding that while compressive strength decreased by up to 68% at 20% PET content, thermal conductivity improved significantly, suggesting potential applications in insulating construction materials like ceiling tiles and brick facings.

Polymers

The composite material with a geopolymer matrix of 7 M molarity, obtained by incorporating microparticles from plastic bottles is developed and characterized in the present paper. To do this, we made cylindrical specimens whose the diameters are the half of their heights and stored them at a temperature of (31±2°C). The compression test using a hydraulic press is carried out, as well as the thermal characterization test using a device respecting the experimental method of the asymmetric hot plane, which was used to determine the thermal conductivity, the volumetric heat capacity, the effusivity and the diffusivity. Then optical characterization tests on hardened samples were carried out, namely chemical analyses of the composition of the kaolin, and particle size characterization of the raw microscopic imaging of the specimens. The results found showed that as the amount of polyethylene terephthalate increases, the compressive strength decreases by 33.65 % for 10%polyethylene terephthalate and 67.77 % for 20 % polyethylene terephthalate. According to the thermal conductivity, it improves with the percentage of polyethylene terephthalate added as: at 10% it is 1.19Wm-1K-1 and at 20%, one has 0.595Wm-1K-1; similarly for effusivity where we obtained 1376.05 JK-1m-2s-1/2 and 560.81 JK-1m-2s-1/2 for 0 and 20% respectively. According to these results, the use of polyethylene terephthalate aggregates as a partial substitute of aluminosilicate raw material for the development of a composite can be a good alternative for recycling plastic bottle waste. The composite obtained could be used for the manufacture of ceiling lights and brick facings, and therefore would significantly reduce the amount of waste plastic produced every day in environment.

More Papers Like This

Article

Promoting Circular Economy in Cementitious Materials: Per-Formance of Cementitious Materials Incorporating Synthesized Composite Aggregates from Recycled Plastic Waste

AI summary Read the abstract

Researchers tested composite mortars made with thermally treated shredded PET bottles replacing up to 100% of natural sand, finding that while higher PET content improved thermal efficiency and reduced density, only 25% substitution met minimum compressive strength standards, supporting PET waste reuse in lightweight sustainable construction.

Article Tier 2

Mechanical, acoustic, and thermal assessment of mortar embedded with polycarbonate particles obtained from end-of-life roofing sheets

AI summary Read the abstract

Researchers found that grinding up old plastic roofing sheets (polycarbonate) and mixing the particles into building mortar actually made it stronger, more heat-resistant, and less brittle—unlike most attempts to reuse plastic waste in construction materials, which usually weaken them. This matters because it offers a practical way to recycle hard-to-reuse plastic waste into sturdier, more energy-efficient building materials, keeping it out of landfills and away from breaking down into microplastics in the environment.

Article

Innovative Composite Aggregates from Thermoplastic Waste for Circular Economy Mortars

AI summary Read the abstract

Researchers developed lightweight synthetic sand (LSS) from dune sand and recycled PET bottles as a natural sand replacement in mortars, finding that up to 25% LSS substitution retains 80% of compressive strength while improving thermal insulation, acoustic properties, and durability, supporting circular economy construction applications.

Article Tier 2

Mechanical, Thermal, and Non-Destructive Evaluation of Concrete Incorporating Recycled PET Bottle Aggregates

AI summary Read the abstract

Researchers incorporated recycled PET bottle aggregates into concrete at up to 30% replacement of natural aggregate, finding that 10% fine PET slightly improves compressive strength while higher substitutions reduce strength by up to 31%, though thermal conductivity drops by up to 42%, making PET-based concrete promising for lightweight insulating applications.

Article

Exploiting recycled plastic waste as an alternative binder for materials used in the construction industry

AI summary Read the abstract

This South African study investigated the feasibility of producing eco-friendly plastic-sand bricks from HDPE plastic waste and river sand, testing six sand-to-plastic ratios with Kaolin Clay DSF additions. Adding 5% Kaolin Clay significantly improved compressive strength from 21.4 MPa to 52.76 MPa in the 75:25 ratio, demonstrating that recycled plastic waste can serve as a viable construction material with improved mechanical and environmental properties.

Research digests by email

When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.

Email me about

Share this paper