We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Enhancing the Mechanical and Rheological Properties of Coal-Based Geopolymer Grouting Materials with Nano-SiO2 and Polypropylene Fibers
AI summary Read the abstract
Adding nano-SiO₂ (1%) to coal-based geopolymer grouting materials reduced water separation by 85.8% and cut gelation time by 51.5%, while polypropylene fiber (1.5%) increased compressive and flexural strength by 43% and 53% respectively. This research contributes to understanding how polypropylene fibers behave in construction materials; fiber degradation over time is a source of microplastic pollution in the built environment.
In order to address the ineffective utilization of industrial solid wastes-particularly fly ash-under the "coal-power integration" model, and to improve the performance of coal-based solid waste geopolymer grouting materials (CBGWG) under dynamic water conditions, this study selected fly ash and coal gangue as the main raw materials to jointly prepare dynamic water grouting slurry. The effects of nano-SiO2 and polypropylene fibers (PPF) on gelation time, initial setting time, bleeding rate, apparent viscosity, compressive strength, and flexural strength were systematically investigated. The experimental results indicate that when the nano-SiO2 content was increased to 1%, the water separation rate decreased by 85.8%, viscosity increased by 17.5%, and both gelation time and initial setting time were reduced by 51.5% and 18.6%, respectively. At a nano-SiO2 content of 0.75% and a PPF dosage of 1.5%, the compressive strength and flexural strength increased by 43.3% and 53%, respectively. However, when the PPF dosage was further increased to 2%, fiber agglomeration occurred during mixing, impairing uniform dispersion. Nano-SiO2 predominantly enhanced the early stiffness of the consolidated body, while PPF significantly improved ductility, residual load-bearing capacity, and energy dissipation, albeit at the expense of some stiffness. These two modifiers exhibited complementary effects in improving the mechanical properties of the grouting material. The optimal dosages of nano-SiO2 and PPF were determined to be 0.75% and 1.5%, respectively, achieving the best balance between mechanical properties and workability.
More Papers Like This
Integrating quarry dust and industrial waste in producing eco-friendly hybrid geopolymer concrete
AI summary Read the abstract
A hybrid geopolymer concrete incorporating industrial plastic waste (plastic shales, pellets) and quarry dust as aggregate substitutes showed comparable or superior mechanical performance to conventional cement concrete, with basalt or dolomite powder replacement increasing compressive strength by ~10%. This is relevant to microplastic research as it demonstrates a pathway to sequester plastic waste into construction materials, potentially reducing plastic fragmentation into environmental microplastics.
Development of a Low-Density Waste-Based Geopolymer Construction Material
AI summary Read the abstract
Researchers developed low-density geopolymer construction materials by incorporating waste fly ash and polystyrene into geopolymer matrices, optimising component mixing ratios, activator concentration, and curing conditions to enhance environmental sustainability and reduce reliance on Portland cement.
Factors Affecting the Performance of Fly Ash–Slag Geopolymers
AI summary Read the abstract
Researchers review recent advances in blast furnace slag and fly ash alkali-activated materials, identifying gaps in how amorphous phase composition, particle size of solid activators, and shrinkage behavior are accounted for in mix design, and calling for more systematic multiobjective optimization to advance one-part geopolymer cements toward industrial adoption.
Potential improvement in the mechanical performance and thermal resistance of geopolymer with appropriate microplastic incorporation: A sustainable solution for recycling and reusing microplastics
AI summary Read the abstract
Researchers tested whether microplastics of various sizes could be incorporated into geopolymer, a cement-like construction material, as a way to recycle plastic waste. Adding small amounts of microplastics actually improved the material's strength and heat resistance up to 400 degrees Celsius. This approach offers a potential solution for trapping microplastics in building materials rather than letting them pollute the environment and threaten human health.
Physical and mechanical properties of fly ash‐based geopolymer with disposable medical mask reinforcement
AI summary Read the abstract
This study incorporated shredded disposable medical masks as reinforcing fibers in fly ash-based geopolymer materials, testing physical and mechanical properties of the resulting composites. The approach offers a way to divert PPE waste from landfills while potentially improving construction material performance.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.