0
Article Sign in to save

Comprehensive Investigation of the Commercial ELP-20 Electron-Beam Lithography Resist

AI summary Read the abstract

Systematic characterization of the ELP-20 electron-beam lithography resist revealed power-law thickness dependencies, an effective molecular weight of ~25 kg/mol, and energy-independent contrast of ~1.67, establishing a performance baseline comparable to PMMA. Understanding the properties of PMMA-like polymer resists directly informs research on microplastic fragmentation behavior, as PMMA is a common plastic pollutant.

Polymers

A systematic experimental study of the positive-tone resist ELP-20 was conducted, covering its structural properties, film-formation behavior, and response to electron-beam exposure. Raman spectroscopy demonstrated the methacrylate nature of the resist and its spectral correspondence to poly(methyl methacrylate) PMMA, which enabled direct comparison both with PMMA itself and with existing methacrylate-based resists. Spin-coated films prepared from 3-11 wt.% solutions exhibited a robust power-law dependence of thickness on spin speed, h∞ ∝ ω-0.48 ± 0.01, and showed high thickness uniformity. The concentration dependence of the film thickness at a fixed spin speed allowed identification of the polymer-coil overlap region and enabled estimation of the effective molecular weight of the polymer base, Meff = (25 ± 7) kg/mol. Lithographic characterization indicated a decrease in sensitivity with increasing electron energy, with a sensitivity of approximately 40 μC/cm2 at 25 keV. A depth-dependent dose-distribution model provided an energy-independent average contrast value of γ ≈ 1.67. The results present a coherent and systematic description of ELP-20 behavior under electron-beam exposure and establish a basis for its further use in lithographic processing.

More Papers Like This

Article Tier 2

Imaging of Non-conducting Beam Sensitive Materials using Scanning Electron Microscopy: Practical Applications of ESEM and LVSEM

AI summary Read the abstract

This thesis examines techniques for imaging non-conducting, beam-sensitive materials like polymers using scanning electron microscopy, comparing environmental SEM (ESEM) and low-voltage SEM approaches. It is a materials characterization methods study with relevance to plastic and polymer analysis.

Article

Designed new modified poly (methyl methacrylate) structures to improve photo resistance

AI summary Read the abstract

This research designs and synthesizes modified poly(methyl methacrylate) (PMMA) polymer structures tailored for environmental remediation applications such as pollutant adsorption or filtration. Chemical modifications to the standard PMMA backbone are used to enhance functional performance in environmental contexts. The new structures offer potential as low-cost, tunable materials for addressing water or soil contamination.

Article Tier 2

Pendant Modification of Poly(methyl methacrylate) to Enhance Its Stability against Photoirradiation

AI summary Read the abstract

Researchers developed pendant modifications to poly(methyl methacrylate) that enhanced its photostability against UV irradiation, demonstrating that strategically attached functional groups can significantly slow polymer degradation and extend material lifetimes.

Article

Sustainable adhesive from waste expanded polystyrene: Performance governed by solvent-substrate interplay

AI summary Read the abstract

Researchers converted post-consumer expanded polystyrene (EPS) waste into high-performance adhesives by dissolving it in organic solvents and blending with PMMA, achieving bond strengths up to nearly 2,000 kPa—demonstrating a practical upcycling route that turns plastic waste into a commercially viable product.

Article Tier 2

Structural Identification and Observation of Dose Rate–Dependent Beam-Induced Structural Changes of Micro- and Nanoplastic Particles by Pair Distribution Function Analysis in the Transmission Electron Microscope (ePDF)

AI summary Read the abstract

Researchers demonstrated that electron pair distribution function (ePDF) analysis of transmission electron microscopy diffraction data can identify and characterise micro- and nanoplastic particles down to 100 nm, distinguishing between polyethylene, polypropylene, PET, polyamide, polystyrene, and silica. The study also revealed dose-rate-dependent beam-induced structural changes in carbon-based polymers, with time-resolved measurements capturing progressive amorphisation under the electron beam.

Research digests by email

When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.

Email me about

Share this paper