We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Trapped microplastics within vertical redeposited sediment: Experimental study simulating lake and channeled river systems during resuspension events
AI summary Read the abstract
Researchers simulated sediment resuspension events to study how microplastics of different densities, sizes, and shapes become trapped within redeposited sediment layers, finding that particle properties strongly influence vertical redistribution patterns in lake and river systems.
Plastic waste and its fragments (microplastics; <5 mm) have been observed in almost all types of environments. However, the mechanisms underlying the flow and transport processes of plastics are unknown. This is particularly valid for river sediments, where complex interactions occur between particles and influence their vertical and horizontal distribution patterns. In this study, we investigated the vertical redistribution of 14 pristine microplastics (MPs) with different densities, sizes, and shapes within disturbed sediment without lateral transport (i.e., low-velocity flow). MPs were spiked into sediments (height: 8 cm) in a column with a height of 1 m (diameter: 6 cm) filled to the top with water. The sediment was perturbed by turning the column upside-down to simulate remobilization and the subsequent deposition of sediment. After the complete sedimentation of the particles, the water column was filtered and the sediment was cut into vertical sections. MPs were then extracted from the sediment using sieves and a density separation method, and were counted under a stereomicroscope. Low-density polymers were mainly recovered in the water column and at the surface of the sediment, whereas high-density polymers were found within all sediment sections. The vertical distribution of high-density polymers changes primarily with the sediment grain size. The distribution of each polymer type changes depending on the size and/or shape of the particles with complex interactions. The observed distributions were compared with the expected distributions based only on the vertical velocity formulas. Overall, the formulas used did not explain the sedimentation of a portion of low-density polymers and predicted a lower distribution in the sediment than those observed in the experiment. In conclusion, this study highlights the importance of considering MPs as multi-dimensional particles and provides clues to understand their fate in low-velocity flow systems, considering that they undergo scavenging in sediments.
More Papers Like This
Different microplastics versus different bottom sediments: transport and accumulation pattern in the open-channel flow experiments
AI summary Read the abstract
Researchers conducted open-channel flume experiments with different microplastic types and bottom sediments to study how particle properties and flow conditions determine where microplastics accumulate or are resuspended. The results show that both plastic particle characteristics and the nature of the underlying sediment influence microplastic transport and deposition behavior in rivers.
Quantifying microplastic particle transport and retention in an experimental flume environment
AI summary Read the abstract
Researchers conducted flume experiments to quantify how microplastic particles of different shapes and densities are transported and retained in artificial river channels under controlled flow conditions. The results show that particle shape and flow dynamics strongly interact to determine where microplastics settle or remain suspended in river systems.
Microplastic trapping in sandy bedload: insights from flume experiments
AI summary Read the abstract
Researchers conducted flume experiments to investigate the mechanisms controlling microplastic trapping in sandy bedload sediments, examining how particles of different sizes and densities become buried within ripple structures formed by unidirectional tractional flows. The study provided insights into riverine microplastic sedimentation dynamics relevant to understanding transient storage during land-to-ocean transport.
Modeling three-dimensional microplastic transport and sedimentation in lakes and reservoirs
AI summary Read the abstract
Researchers used 3D hydrodynamic modeling to simulate microplastic transport, residence time, and sedimentation patterns in lakes and reservoirs. The models showed that bathymetry and inlet-outlet flow patterns strongly control where microplastics accumulate on lake beds.
The initiation and resuspension characteristics of (micro)plastics from varied depositional environments under hydraulic disturbance
AI summary Read the abstract
Scientists found that microplastics settled in riverbeds and lakebeds can get stirred back up into the water when currents reach a certain speed, and how easily this happens depends on the plastic's type, shape, and the kind of sediment it's buried in. This matters because it means microplastics we thought were "trapped" in waterway sediments can re-enter the water we drink, fish from, and rely on for ecosystems, making pollution harder to predict and contain than previously thought.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.