We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
Towards quantitative microplastic analysis using pyrolysis-gas chromatography coupled with mass spectrometry
AI summary Read the abstract
Researchers worked to improve a lab technique called pyrolysis-GC/MS — which identifies plastics by heating them until they break apart into detectable chemical fragments — and found that mixing certain plastics together (especially PVC with others) produces unexpected reactions that can throw off measurements. Their findings highlight the urgent need for standardized international methods so that microplastic data from different labs can be reliably compared.
Microplastic pollution from everyday plastic items has increased tremendously worldwide. Pyrolysis gas chromatography coupled to mass spectrometry (Py-GC/MS) has been widely investigated for the qualitative and quantitative analysis of microplastics in environmental samples. However, there are several pitfalls to consider when developing an appropriate protocol for their analysis. This study aimed at the development of an in-house database of primary (single) polymers, binary (two) polymers and tertiary (three) polymer mixtures. In this context the potential occurrence of gas phase reactions during pyrolysis of binary and tertiary polymers were investigated. Further, different diluters were tested for the accurate preparation of calibration standards for quantification purposes. Seven different polymers were included in this study, which were chosen due to their prevalence in daily plastic appliances. For each single polymer specific peaks could be identified and recommendation for quantifier analytes given. The analysis of binary polymer mixtures revealed gas phase reactions for PET with PVC, PVC with MDI-PU and PE with PVC. For these binary polymers, several different novel pyrolysis products, specific for the according binary polymer mixture, could be identified. These results confirmed that especially PVC exhibits strong interactions during co-pyrolysis with ester- and ether-based polymers. Similar results were obtained for tertiary polymers. For accurate preparation of calibration standards different diluters (silica, deactivated silica, calcium carbonate, THF and HFIP) were tested. It was observed that deactivated silica had only an influence on the pyrolysis of PET. Whereas, dilution with silica affected PA-6/66, PE, PET and MDI-PU. Only PVC was not influenced by dilution with silica. In conclusion, our results highlight the necessity of an international standard of reference material as well as a standardized analytical protocol for the analysis and quantification of polymers in environmental samples. It is crucial to use diluters suitable for the specific polymer, to exclude potential interactions of diluters with the polymer. The present work has to be seen as a foundation, but future work is needed to adequately address the quantification of polymers in environmental samples. • In-house database built with single, binary and tertiary polymer mixtures. • Gas phases of binary and tertiary polymer mixtures investigated. • Diluters of polymer reference standards investigated for quantification purposes.
More Papers Like This
Secondary reactions in the analysis of microplastics by analytical pyrolysis
AI summary Read the abstract
Polymer interactions during analytical pyrolysis of mixed microplastic samples were investigated, finding that co-pyrolysis of PET with PVC and polyamides produces secondary reaction products not characteristic of any individual polymer, which could compromise the accuracy of pyrolysis-GC-MS identification in real environmental samples.
Quantitation of polystyrene by pyrolysis-GC-MS: The impact of polymer standards on micro and nanoplastic analysis
AI summary Read the abstract
Researchers evaluated how the choice of polystyrene reference standard affects the accuracy of a key method (Pyrolysis-GC-MS) used to detect and measure microplastics and nanoplastics, finding that different standards with varying molecular structures produce substantially different results for the same sample. This highlights an urgent need for standardized reference materials to make microplastic measurement methods more reliable and comparable across labs.
Standardizing pyrolysis gas chromatography mass spectrometry for nanoplastics and microplastics detection to advance environmental research
AI summary Read the abstract
Researchers proposed four key recommendations for standardizing how pyrolysis gas chromatography-mass spectrometry is used to detect nano- and microplastics in environmental samples. The recommendations cover sample preparation, scalable heating methods, product selection for measurement, and AI-assisted data analysis. Standardizing these techniques is important because inconsistent methods across laboratories make it difficult to compare microplastic pollution data worldwide.
Microplastics analysis in environmental samples – recent pyrolysis-gas chromatography-mass spectrometry method improvements to increase the reliability of mass-related data
AI summary Read the abstract
This study improved pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) methods for measuring mass-related microplastic data in environmental samples, enhancing reliability and sensitivity for trace-level analysis. Better analytical methods are essential for accurately quantifying microplastic contamination across diverse environmental matrices.
Simultaneous Trace Identification and Quantification of Common Types of Microplastics in Environmental Samples by Pyrolysis-Gas Chromatography–Mass Spectrometry
AI summary Read the abstract
Researchers developed a method for simultaneous trace identification and quantification of common microplastic types in environmental samples, improving detection efficiency and enabling more accurate monitoring of multiple plastic polymers at once.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.