We can't find the internet
Attempting to reconnect
Something went wrong!
Hang in there while we get back on track
The behaviour of plastic particles during pyrolysis in bubbling fluidized bed reactors: Incipient agglomeration and axial segregation
AI summary Read the abstract
This study used X-ray imaging techniques to investigate the behavior of single polypropylene particles during pyrolysis in a bubbling fluidized bed reactor at 500–650°C. Results showed that the sinking-floating behavior of plastic particles is not simply explained by density changes from sand-plastic agglomerate formation, with axial segregation and stochastic models better capturing the complex dynamics observed.
Plastics-fluidized bed interaction has been investigated by non-invasive X-ray imaging techniques in the temperature range of 500–650 °C and under pyrolysis conditions. Experiments were conducted by feeding a single polypropylene particle using either overbed or underbed feeding methods. The fluidized bed was operated from minimum fluidization conditions to bubbling regime, up to 2Umf. Interestingly, experimental observations show that the understanding of the mixing/segregation behaviour of polypropylene in a hot fluidized bed does not appear to be as straightforward as in the case of more conventional feedstocks, such as biomass. Further analysis and an alternative point of view to investigate the complex behaviour observed for plastic feedstock have been provided. The interaction between the fluidized bed and a single polypropylene particle was modelled by means of an axial segregation model, and a physics-assisted stochastic approach. In the second case, it was possible to simulate the formation of the sand-plastic agglomerate (incipient agglomeration stage) and the evolution of its density over time. The models were then validated by means of axial segregation data obtained via X-ray imaging techniques and by measuring the physical properties of real sand-polypropylene agglomerates produced within the bed operating at high temperatures. Results obtained in this study show that the unpredictable sinking-floating behaviour of the plastic particles is not related to the change in density associated to the formation of the sand-polypropylene agglomerates over time.
More Papers Like This
Determination of sand mass flow rate in a test reactor
AI summary Read the abstract
This thesis measured bed material mass flow rate in a fluidized bed test reactor for plastic pyrolysis, providing data needed to optimize conditions for converting plastic waste into fuel as a circular economy strategy to address the growing global plastic recycling gap.
Process Simulation Modeling of the Linear Low-Density Polyethylene Catalytic Pyrolysis in a Fluidized Bed Reactor
AI summary Read the abstract
Researchers developed a process simulation model for the catalytic pyrolysis of linear low-density polyethylene in a fluidized bed reactor, finding that temperature significantly influences the yield of fuel-range oil and wax products from plastic waste.
Design and Performance of a Two-Stage Fluidized Bed Reactor for Catalytic Pyrolysis of Mixed Plastic Waste
AI summary Read the abstract
A two-stage fluidized bed reactor using a custom Ni/γ-Al2O3 catalyst achieved 90% yield of pyrolysis oil and waxes from mixed PE, PP, PET, and PS waste at 400–453°C, producing hydrocarbon feedstocks suitable for the chemical industry. Catalytic pyrolysis as a chemical recycling route for mixed plastic waste is significant for microplastic pollution research because it offers a scalable end-of-life pathway that prevents plastic from fragmenting into environmental microplastics.
Accumulation of Ash-Forming Elements in Blast-Furnace Slag Bed Material during Fluidized Bed Combustion of Woody Biomass, Sludge, and Plastic Waste
AI summary Read the abstract
Researchers tested burning wood, sludge and plastic waste together with blast-furnace slag (a material used instead of sand) in a pilot-scale furnace. Compared to sand, the slag collected less coating from alkali metals, which can cause clumping problems, while heavy metals built up when sludge was used and titanium and antimony increased with plastic-containing fuels.
Catalytic Pyrolysis of Polypropylene to Benzene, Toluene, and Xylene (BTX) Using a Double-Fluidized-Bed Reactor
AI summary Read the abstract
Researchers demonstrated catalytic pyrolysis of polypropylene waste in a continuous double-fluidized-bed reactor to produce benzene, toluene, and xylene (BTX), achieving a 22.3 wt% BTX yield at 550°C. The reactor showed stable operation over 10 hours, with smaller catalyst particle sizes and lower nitrogen flow rates favoring BTX formation, though coke deposition gradually reduced catalyst activity.
Research digests by email
When a large batch of papers lands in the Atlas, we read through it and send a short write-up of what stood out.